iForm Motion Bed MA-Series Owner Manual (Installation and Operation Guide)

iForm Motion Bed MA-Series Owner Manual (Installation and Operation Guide)


OWNER MANUAL
Installation & Operation
iForm
MA-1000/MA-2000(S)(M)/MA-3000M/MA-4000M



READ THE FOLLOWING INFORMATION CAREFULLY BEFORE USING THIS PRODUCT

If unable to understand warnings, cautions, and/or instructions, contact the dealer or technical personnel
if applicable, before attempting to use the equipment. Otherwise, injury or damage may result.

SAFETY WARNINGS

•      Do not use bed outdoors.
•      Do not use bed near explosives.
•      Using bed with oxygen administering equipment other than the nasal masked type creates a possible fire hazard.
•      When using nasal or masked type administering equipment, route and secure oxygen or air tubing properly to ensure that tubing does not become entangled or damaged during normal operation of the bed.
•      Use caution when having liquids in or around the bed to ensure no spilling occurs. In case of spillage, stand in a dry, clean area of the floor and unplug the bed immediately. Clean up spill and allow the area around bed to dry thoroughly before using the electric controls again. Do not eat or drink hot liquids while operating the bed.
•      This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given
supervision or instructions concerning use of the appliance by a person responsible for their safety.
•      Do not allow any person or pet under the bed at any time.
•      During bed operation, make sure body is positioned within the confines of the bed. Do not place extremities over the sides of the bed when operating bed functions.

WARRANTY WARNINGS

Do not open or tamper with control box, motors, or remote (except for battery compartments). The warranty will be void if the internal workings of these components are tampered with.

Product Rating

The motors are not designed to operate continuously for more than [2] minutes in an [18] minute time period or approximately 10% duty cycle. Attempting to circumvent or exceed this rating will shorten the life expectancy of the foundation and may void the warranty.

Operating Information

•      After the power foundation assembly is completed, operate remote control to ensure proper functions.
•      Keep moving parts free of obstruction during bed operation (including sheets, clothing, tubing, wiring, and products using electric power cords).
•     Evenly distribute body weight over bed surface. Do not place entire weight on head or foot sections of the bed, during re-positioning and entering or exiting bed. 

Hospital Use Disclaimer

This power foundation is designed for residential use only. It is not approved for hospital use and does not comply with hospital standards.

Weight Limits

This product is not rated to support weights more than 340 KG inclusive of the mattress and bedding. The bed will structurally support this weight, provided it is evenly distributed across the foundation. The power foundation is not designed to support or lift this amount in the head or foot sections alone. Exceeding this weight restriction could damage the bed and/or cause injury and will void the warranty.



Parts List


All electronics and components that need to be installed are located in boxes under the foundation or attached to the frame. Before discarding the packing materials, ensure that all the parts are accounted for.



Actual product appearance and functionality may vary from photographs.

iForm 1000 / MA-1 Electronics Quick Reference Guide

OVERVIEW






iForm 2000(S) / MA-2 Electronics Quick Reference Guide

OVERVIEW





iForm 2000M / MA-2 MASSAGE Electronics Quick Reference Guide

OVERVIEW




MA-3 MASSAGE Electronics Quick Reference Guide

OVERVIEW




MA-4 MASSAGE Electronics Quick Reference Guide

OVERVIEW



Installation Guide

Take care and appropriate measures to ensure the safe handling of the product given its weight.



STEP 1

Place the foundation box in a desired location with the bottom of the box facing up. Remove the binding straps and packing materials, making sure not to puncture the box with any sharp objects.



STEP 2
Remove the foundation from the box, keeping the bottom of the foundation facing upward for easier access to the bed's components.

STEP 3
To install the legs, thread the bolt of the leg to the nut on the foundation frame, and tighten by hand. DO NOT OVER-TIGHTEN.

STEP 4
Uncoil the input power cord (connected to the control box’s power port) and plug it into the power supply.



STEP 5
Uncoil the power cord and connect it to the power supply.



STEP 6
Battery back up in case of power blackout.



STEP 7
Carefully flip the foundation over onto its legs.

Important: Two people are required to move the foundation. Do not drag across the floor. Do not rest frame on its side; excessive pressure may damage the legs.

STEP 8
Ensure that batteries are correctly installed.



STEP 9
Locate the mattress retainer bar brackets.

Slide the left side of the mattress retainer bar into the bracket. Pull the retainer bar to the opposite bracket and secure the right side.



iForm 1000 / MA-1 Remote Control Instructions





iForm 2000(S) / MA-2 Remote Control Instructions



iForm 2000M / MA-2 MASSAGE Remote Control Instructions




iForm 3000M / MA-3 MASSAGE Remote Control Instructions



iForm 4000M / MA-4 MASSAGE Remote Control Instructions




Setting Programmable Positions and Pairing Remote

SETTING PROGRAMMABLE POSITIONS


The wireless power bed has programmable features that allows you to save custom positions. Please read all the instructions below before setting your custom presets on the remote.

STEP 1

Adjust the head and foot to your desired position.



STEP 2

Press and hold the flat button first, then press and hold memory button for 5 seconds until you hear 2 beeps sound.



STEP 3

To adjust the saved position, repeat steps 1 and 2 and the new position will be saved.

PAIRING REMOTE

The original remote that comes in the box is already paired to the foundation. No further action is required. In the event that the remote is not paired with the foundation, follow the steps below.

STEP 1

Make sure the batteries work fine. Replace them when needed.



STEP 2

Plug the power cord to the power source.



STEP 3

Example:

For BT1000

Press and hold Head Lifting and Foot Lifting buttons simultaneously, then press and hold the Reset button on the cord of control box for 3 seconds until you hear 2 beeps indicating the remote has been paired.



For more information regarding to the pairing of remote controllers. Please visit:  https://support.mlily.com.au/portal/kb/articles/how-to-pair-the-remote-controllers

Synchronizing Two Bases

If simultaneous operation of two foundations is desired, please read pairing remotes instructions of PARING REMOTE.

STEP 1

Plug A and B bases to power source.



STEP 2

Make sure remote A is already paired to base A and remote B paired to base B. If not, please pair them by following the pair remote instructions on PARING REMOTE.

STEP 3

Pair remote A to base B, then base A and base B for simultaneous operation by remote A.



STEP 4

Set Remote B to operate both bases too.

For MA-2SM (or 2M) / MA-3SM (or 3M) / MA-4SM (or 4M), please follow the instructions below.
Press and hold Head Down and Foot Down buttons on remote B, at the same time (simultaneously) press and hold Head Up and Foot Up buttons on Remote A, the learning process is successful when the flashlight on remote B starts to flash.

Now both remotes will be able to operate both beds simultaneously.





N.B. For MA-1 / MA-2(S), only one remote can control both bases.


Headboard Bracket Installation Guide

Headboard brackets are an optional accessory and are not included.
A 1/2'' (13 mm) socket and 1/2'' (13 mm) crescent wrench are necessary to complete installation.

HEADBOARD BRACKET COMPONENTS



STEP 1

The headboard bracket will have 2 long slots to accommodate any frame type. Align the appropriate slots on the bracket with the holes on the bed. Use long bolts and nuts to secure the bracket. Make sure the bolts are tight.



STEP 2

To put the T-Bracket and Headboard Bracket together, you will need (2) short bolts and (2) nuts. Thread the bolts through the holes from T-Bracket to Headboard Bracket with the head of bolt facing outward. Use 1/2'' (13mm) socket and 1/2'' (13mm) wrench to tighten the bolts.



STEP 3

Connect your headboard to the attachment plates using the remaining short bolts and nuts to secure it to the brackets. The heads of the bolts will face outward. Use a 1/2" (13 mm) socket and 1/2" (13 mm) wrench to tighten the bolts.

Troubleshooting

In the event of per failure the foundation fails to operate, assess the symptoms and possible solutions provided in the table below.


SYMPTOMS
SOLUTIONS
Remote control illuminates and appears to be operable, but will not activate bed.

Verify that the power cord is plugged into a working, grounded electrical outlet. Test the outlet by plugging in another working appliance.
No features of the power foundation will activate.

Program the remote control (see the setting programmable positions and pairing remote section of this manual for programming procedures).

Unplug the power cord, wait 30 seconds and plug back to reset electronic components.

The surge protection device or the electrical outlet may be defective.

Test the outlet by plugging in another working appliance.

Verify that the connector on the wired remote control is securely attached to the control box.

Wireless remote will not illuminate.

Replace the batteries in the wireless remote.

Head or foot section will elevate, but will not return to the horizontal (flat) position.

Bed mechanism may be obstructed. Elevate bed and check for obstruction. Remove obstruction.

Head section may be too close to the wall.

Headboard may be too close to the edge of the mattress. Verify that there is enough distance between the headboard brackets and mattress. Adjust if required.

Head or foot section will elevate, but will not return to the horizontal (flat) position.

Bed mechanism may be obstructed. Elevate bed and check for obstruction.

Remove obstruction.

Head section may be too close to the wall.

Headboard may be too close to the edge of the mattress. Verify that there is enough distance between the headboard brackets and mattress.

Adjust if required.

Head & Foot lift function has minor interference during operation.

Check batteries in wireless remote control, replace with two (2) new AAA batteries if necessary.

Make sure that you are following the duty cycle of the motors (do not operate more than two minutes over a 18-minute period, or approximately 10% duty cycle).

Press the lift buttons squarely and accurately.

Wireless remote control may be experiencing common Radio Frequency Interference from other radio transmitting devices. Wait several seconds, and then try pressing appropriate button again, See FCC Compliance Statement on page 1 of this guide.

Excessive massage motor noise.

If the bed is located on hard surface flooring, place carpet pieces or rubber pieces (not included) under each leg.

Using the wireless remote control, elevate the head, foot or neck section a short distance to realign the lift/lower mechanisms with the bed support platform.

Verify that your Power Foundation is not positioned against a wall, nightstand, or other object that may cause the vibration or noise.

If the Power Foundation is installed over a bed frame, verify that the massage motors are not causing the bed frame (or bed frame components) to vibrate.

Verify that the headboard attachment hardware is properly tightened (if used).
A clicking noise is heard under the bed when raising or lowering.

This is normal. The lift motor relays “click” when they are engaged.

No action is required.

Massage motor overheats or stops.

If the vibration motor overheats, the thermal protection will turn the motor off.

Wait 30 minutes, turn the massage back on.

If it does not come on, turn it off and report the situation to customer service.





    • Related Articles

    • iForm How to use one remote control to work on two motion beds (MA-Series)

      1. Review your operation manual on how to pair the remote controls with the motion bed: click below link. https://support.mlily.com.au/portal/en/kb/articles/how-to-pair-the-remote-controls 2. Use ONE remote control to pair with ONE motion bed; 3. Use ...

    • How to pair the remote controls iForm (MA Series)?

      For ONE motor motion bed products (e.g. MA1 and 1000): 1. Press and hold the "Head Up" and "Head Down" buttons together; 2. Press the RESET button on the power cord (connected to the control box); 3. If you hear a beep sound, the synchronization has ...

    • Premier Base headboard installation instructions

      We are excited to inform you that the video instructions for the Premier headboard are now available. The instructional video has been included below for your convenience and are also accessible on our portal and other MLILY support platforms. We ...

    • Cable Restraint Cover

      It is important to remove the cable restraint cover before plugging the cables in to the control box. Failing to remove the Cable Restraint Cover from the control box may cause damage or inadequate connection of cables. The improper connection ...

    • Bedhead installation iActive

      The iActive (B200/B253) bedhead should come with the following: 8 x Long bolts with nuts 2 x Brackets 4 x Short bolts Additionally, you will need a socket and wrench (or similar) for assembly. Start by attaching the brackets to the bedhead using the ...